Items 1- 32 of 197 total

Sport Bar Fire Extinguisher Holder, Black, 55-14 Jeep CJ and Wrangler Sport Bar Fire Extinguisher Holder, Black, 55-14 Jeep CJ and Wrangler
Online
$23.18 for EA
Retail $29.99
Mfr PN: 13305.21
Stock: 5
Special designed holder incorporates thick nylon web straps that secures your Fire Extinguisher to the roll bar. Straps are fully adjustable and secure with hook and loop fasteners and will hold up to a 4 diameter fire extinguisher. Fits up to a 3 roll bar with or without padding.
Online
$23.18 for EA
Retail $29.99
Mfr PN: 13305.21
Stock: 5

GM 8.5in. 10 Bolt Rear High Capacity Cover GM 8.5in. 10 Bolt Rear High Capacity Cover
Online
$294.66 for EA
Retail $434.60
Mfr PN: GM10-8.5
Stock: 10
Mag-Hytec's heavy duty differential covers and transmission pans provide increased lubricant and cooling capacity for hard working recreational and service vehicles. Mag-Hytec covers and pans set your vehicle apart in both aesthetics and function cast in A356-T6 aluminum and texture powder coated black With machined cooling fins. Magnetic drain plugs trap worn gear material promoting fluid integrity. Each unit is fitted with ARP 568 O-rings for superior sealing. All hardware is 303 stainless steel, in most applications no gasket or sealant is required, and all Mag-Hytec parts are covered by a lifetime limited warranty. Depend on Mag-Hytec when you're pulling a heavy load. For Use On GM 8.5in./8.6in. Rear Axles Only Finned Aircraft Aluminum Housing For Improved Cooling Black Powder Coat Finish Holds 2 Extra Quarts Of Oil Overall Height Is 3 1/4in. Offers Easy Routine Maintenance Without Removing The Differential Cover Dipstick With Magnetic Insert
Online
$294.66 for EA
Retail $434.60
Mfr PN: GM10-8.5
Stock: 10

DANA 44 DIFF COVER DANA 44 DIFF COVER
Online
$120.12 for EA
Mfr PN: 42-11-044
Stock: 254
Poison Spyder Bombshell Diff Covers are designed to protect your gears, lockers and diff cover bolts from the most punishing rocks and trail hazards. The stock covers your Jeep came with are weak, stamped sheetmetal. Even a moderate tap with a rock can cave it in against your ring gear, causing potential damage to the gears, locker and carrier bearings, not to mention a difficult, messy trail fix. Even more common, though less catastrophic, is "peel back" that can occur when sliding over a rock causes the lip of the cover to peel up, allowing your gear oil to drain causing a hazard for both your Jeep and the environment. The Bombshell Diff Cover is your best insurance against each of these hazards. The Bombshell differential cover is cast from highly ductile nodular iron—the same material drag racing differential housings are cast from to handle thousands of horsepower. The design of the Bombshell incorporates recesses to protect the diff cover bolt heads from trail damage, while the profile of the Bombshell acts as a ramp to help slide your Jeep up and over the most troublesome pumpkin-eaters. The ramp profile also results in an extremely thick & up to 1" thick—cross-section around the bolt ring, where contact with the rocks is most likely. Throughout the rest of its cross-section the Bombshell is the thickest cast differential cover on the market, from 7/16" to a brutal 1/2" thick at the outermost surface.
Online
$120.12 for EA
Mfr PN: 42-11-044
Stock: 254

Roll Bar Mounted Fire Extinguisher Holder - 2.5lb. Roll Bar Mounted Fire Extinguisher Holder - 2.5lb.
Online
$20.99 for EA
Mfr PN: 769540
Stock: 723
This handy 2.5 pound fire extinguisher holder will keep your extinguisher stored safely and securely to your off-road rig's 2-3 inch roll bar and off of the floorboard during dicey off-road driving conditions. Use with 1.5-4 inch Sport/Roll Bar Attaches using heavy-duty hook and loop straps Works with 2.5 pound Fire Exinguishers Available in black only
Online
$20.99 for EA
Mfr PN: 769540
Stock: 723

C-PILLAR KIT C-PILLAR KIT
Online
$179.98 for EA
Mfr PN: 18-18-030
Stock: 13
For those looking to further enhance the JK 4-Door Trail Cage installation, the Poison Spyder C-Pillar Kit ads strength to the rear passenger portion of the OE cage. This kit must be welded in to the OE cage at the top, but it bolts in at the lower end. The C-Pillar kit consists of CNC laser cut lengths of 1.75" OD, .120" wall DOM tubing, and engineered foot plates that are fabricated from CNC laser cut, brake-formed 3/16" plate steel. Convenient indexing tabs and slots are provided where the DOM tube connects with the foot plate, making assembly quick and easy.
Online
$179.98 for EA
Mfr PN: 18-18-030
Stock: 13

Tube Clamps Tube Clamps
Online
$42.60 for EA
Mfr PN: 180127-KIT
Stock: 1
Trail-Gear O.D. Tube Clamps are ideal for suspension and steering brackets that you need attached to a section of tubing when you don’t want to weld the bracket directly to the tubing because adjustment or frequent removal of the bracket is needed. The O.D. Tube Clamp is perfect for attaching shock brackets to suspension link or steering brackets to steering rods or links and allows you to attach steel mounting brackets that are readily available to aluminum suspension links and steering rods that you could not otherwise weld steel brackets to. Manufactured from 1020 steel, with a clamping force of up to 8,600lbs these tube clamps will not fail even under the most extreme circumstances. Sold Individually.
Online
$42.60 for EA
Mfr PN: 180127-KIT
Stock: 1

GUSSET TRIANGLE CUTOUT GUSSET TRIANGLE CUTOUT
Online
$3.48 for EA
Retail $5.99
Mfr PN: 120086-KIT
Stock: 11
Weld in frame gussets. Each gusset measures 3" tall by 3" wide. Made from 3/16" mild plate steel.
Online
$3.48 for EA
Retail $5.99
Mfr PN: 120086-KIT
Stock: 11

GUSSET TRIANGLE BLANK GUSSET TRIANGLE BLANK
Online
$3.48 for EA
Retail $5.99
Mfr PN: 120087-KIT
Stock: 2
Weld in frame gussets. Each gusset measures 3" tall by 3" wide. Made from 3/16" mild plate steel.
Online
$3.48 for EA
Retail $5.99
Mfr PN: 120087-KIT
Stock: 2

2.5 lb. HalGuard Red Clean Agent Fire Extinguisher 2.5 lb. HalGuard Red Clean Agent Fire Extinguisher
Online
$182.17 for EA
Mfr PN: HG250R
Stock: 6
HalGuard is no ordinary fire extinguisher. It contains an electrically non-conductive"clean" extinguishing agent that rapidly turns into a gas. The clean agent used in HalGuard has passed extensive testing by Underwriters Laboratories, and meets FAA requirements. It can be found on commercial aircraft, and is used by airport fire fighters and on the flight line. Hand held HalGuard extinguishers are available in either compact 1.4 lb. and 2.5 lb. sizes, or larger 5 lb., 11 lb., and 15.5 lb. units. The larger sizes are USCG approved, and meet DOT requirements for the heavy duty truck market. 65 lb., and 150 lb. wheeled HalGuard extinguishers offer maximum clean agent protection for the pit lane or large facilities.
Online
$182.17 for EA
Mfr PN: HG250R
Stock: 6

Ford 8.8in. Aluminum Cover Ford 8.8in. Aluminum Cover
Online
$129.99 for EA
Mfr PN: 40-2013AL
Stock: 71
G2 aluminum differential covers are designed to not only protect your ring & pinion, they are designed to help cool your gear oil for prolonged bearing life. Made from high strength heat treated aluminum to withstand direct hits, these covers help protect your investment while adding a distinct look to your vehicle. For Use On Ford 8.8in. Rear Axles Cast From Lightweight Aluminum To Dissipate Heat Raw Aluminum Finish ReinForcing Ribs For Added Rigidity And Strength Heat Treated And Shot Peened To Help Handle A Direct Impact Fully Machined Seal Surface For A Leak Free Installation
Online
$129.99 for EA
Mfr PN: 40-2013AL
Stock: 71

Interlocking Tube Clamps Interlocking Tube Clamps
Online
$37.04 for EA
Mfr PN: 180114-KIT
Stock: 4
Need to place a support tube across your truggy or buggy, but need the flexibility to remove a motor, transmission, or even a seat? We have the perfect solution for you, Trail-Gear’s Interlocking Tube Clamps. They are machined from 100% 4130 Chromoly and use a counter sunk allen head screw.
Online
$37.04 for EA
Mfr PN: 180114-KIT
Stock: 4

FIRE EXTINGUISHER MOUNT FIRE EXTINGUISHER MOUNT
Online
$70.14 for EA
Retail $74.99
Mfr PN: FIREX-MNT-DOR
Stock: 70
NHRA approved, the Drake Fire Extinguisher Mount is machined from 6061-T6 billet aluminum with a black anodized finish and a laser etched logo. Features include a red anodized quick release knob, and a versatile mounting options. Fits various sizes of automobile fire extinguishers. Requires part number DRKFIRE-CLMP-S-DOR or DRKFIRE-CLMP-L-DOR.
Online
$70.14 for EA
Retail $74.99
Mfr PN: FIREX-MNT-DOR
Stock: 70

Trail Gear Gusset, Web 120083-KIT Trail Gear Gusset, Web 120083-KIT
Online
$3.48 for EA
Retail $5.99
Mfr PN: 120083-KIT
Stock: 13
Weld in frame gussets. Each gusset measures 3" tall by 3" wide. Made from 3/16" mild plate steel.
Online
$3.48 for EA
Retail $5.99
Mfr PN: 120083-KIT
Stock: 13

3" Diameter Fire Extinguisher Mount Clamp 3" Diameter Fire Extinguisher Mount Clamp
Online
$21.92 for EA
Retail $21.99
Mfr PN: FIRE-CLMP-L-DOR
Stock: 1
Clamps for use with FIREX-MNT-DOR.
Online
$21.92 for EA
Retail $21.99
Mfr PN: FIRE-CLMP-L-DOR
Stock: 1

Paracord Grab Handle û Roll Bar Paracord Grab Handle û Roll Bar
Online
$60.37 for EA
Mfr PN: TAOGHUPBU
Stock: 43
The Paracord Grab handles are made from the same cord material that you can find on parachutes. The material is woven into a tough looking grab hand and will fit padded or non-padded roll bars. They have metal hardware and a griping backing so that they stay put when you’re pushing the vehicle to the limits. Trek Armor has over 17 years of combined experience in manufacturing cutting and sewing products for the U.S. military, you can be sure that what we produce is absolutely top of the line.
Online
$60.37 for EA
Mfr PN: TAOGHUPBU
Stock: 43

Ford 10.25in./10.5in. High Capacity Cover Ford 10.25in./10.5in. High Capacity Cover
Online
$300.81 for EA
Retail $426.40
Mfr PN: 12-10.25/12-10
Stock: 46
Mag-Hytec's heavy duty differential covers and transmission pans provide increased lubricant and cooling capacity for hard working recreational and service vehicles. Mag-Hytec covers and pans set your vehicle apart in both aesthetics and function cast in A356-T6 aluminum and texture powder coated black With machined cooling fins. Magnetic drain plugs trap worn gear material promoting fluid integrity. Each unit is fitted with ARP 568 O-rings for superior sealing. All hardware is 303 stainless steel, in most applications no gasket or sealant is required, and all Mag-Hytec parts are covered by a lifetime limited warranty. Depend on Mag-Hytec when you're pulling a heavy load. For Use On Ford 10.25in./10.5in. Sterling Rear Axles Finned Aircraft Aluminum Housing For Improved Cooling Black Powder Coat Finish Holds 2.5 Extra Quarts Of Oil(6 Total) Overall Height Is 3 7/8in. Offers Easy Routine Maintenance Without Removing The Differential Cover Dipstick With Magnetic Insert
Online
$300.81 for EA
Retail $426.40
Mfr PN: 12-10.25/12-10
Stock: 46

Wrangler Roll Bar Clamp Wrangler Roll Bar Clamp
Online
$73.46 for EA
Mfr PN: ABC-2465
Stock: 0
So you say you just can't bear to remove that nice rollbar padding on your YJ, TJ, LJ, or new JK. I hear ya. Leave the padding on and still be able to clamp your bracket to your rollbar with these wider cut Rollbar Clamps. They also fit 2 3/8" dia. (Bronco) and 2 1/4" dia. tubing (Wrangler without padding). 2004 and later Wrangler owners, note that there may be an extra layer of rigid foam beneath the zippered padding and a small amount of it will have to be removed to allow the clamp bolts to get started. Large black pair Billet aluminum Fits 2-3/8" and 2-1/4" diameter roll bars
Online
$73.46 for EA
Mfr PN: ABC-2465
Stock: 0

FIRE EXTINGUISHER HOLDER FIRE EXTINGUISHER HOLDER
Online
$32.38 for EA
Mfr PN: 57-62-110
Stock: 474
The velcro straps that hold this unit to the roll bar are optimally sized for use on padded roll bars. When using on bare, un-padded tubes (1.75" OD or larger recommended), the ends of the velcro straps wlll be too long, but can either be tucked in or cut off (use a lighter to cauterize the cut edge of the nylon webbing).
Online
$32.38 for EA
Mfr PN: 57-62-110
Stock: 474

DANA 30 DIFF COVER - PC DANA 30 DIFF COVER - PC
Online
$132.10 for EA
Mfr PN: 42-11-030-PC
Stock: 459
Poison Spyder Bombshell Diff Covers are designed to protect your gears, lockers and diff cover bolts from the most punishing rocks and trail hazards. The stock covers your Jeep came with are weak, stamped sheetmetal. Even a moderate tap with a rock can cave it in against your ring gear, causing potential damage to the gears, locker and carrier bearings, not to mention a difficult, messy trail fix. Even more common, though less catastrophic, is "peel back" that can occur when sliding over a rock causes the lip of the cover to peel up, allowing your gear oil to drain causing a hazard for both your Jeep and the environment. The Bombshell Diff Cover is your best insurance against each of these hazards. The Bombshell differential cover is cast from highly ductile nodular iron—the same material drag racing differential housings are cast from to handle thousands of horsepower. The design of the Bombshell incorporates recesses to protect the diff cover bolt heads from trail damage, while the profile of the Bombshell acts as a ramp to help slide your Jeep up and over the most troublesome pumpkin-eaters. The ramp profile also results in an extremely thick & up to 1" thick—cross-section around the bolt ring, where contact with the rocks is most likely. Throughout the rest of its cross-section the Bombshell is the thickest cast differential cover on the market, from 7/16" to a brutal 1/2" thick at the outermost surface.
Online
$132.10 for EA
Mfr PN: 42-11-030-PC
Stock: 459

Dana 44 Aluminum Cover Dana 44 Aluminum Cover
Online
$129.99 for EA
Mfr PN: 40-2033AL
Stock: 386
G2 aluminum differential covers are designed to not only protect your ring & pinion, they are designed to help cool your gear oil for prolonged bearing life. Made from high strength heat treated aluminum to withstand direct hits, these covers help protect your investment while adding a distinct look to your vehicle. For Use On Dana 44 Front Or Rear Asxles Cast From Lightweight Aluminum To Dissipate Heat Raw Aluminum Finish ReinForcing Ribs For Added Rigidity And Strength Heat Treated And Shot Peened To Help Handle A Direct Impact Fully Machined Seal Surface For A Leak Free Installation
Online
$129.99 for EA
Mfr PN: 40-2033AL
Stock: 386

Dana 25/27/30 Aluminum Cover Dana 25/27/30 Aluminum Cover
Online
$119.99 for EA
Mfr PN: 40-2031AL
Stock: 289
G2 aluminum differential covers are designed to not only protect your ring & pinion, they are designed to help cool your gear oil for prolonged bearing life. Made from high strength heat treated aluminum to withstand direct hits, these covers help protect your investment while adding a distinct look to your vehicle. For Use On Dana 25/27/30 Front Axles Except KJ Cast From Lightweight Aluminum To Dissipate Heat Raw Aluminum Finish ReinForcing Ribs For Added Rigidity And Strength Heat Treated And Shot Peened To Help Handle A Direct Impact Fully Machined Seal Surface For A Leak Free Installation
Online
$119.99 for EA
Mfr PN: 40-2031AL
Stock: 289

Dana 35 Aluminum Cover Dana 35 Aluminum Cover
Online
$129.99 for EA
Mfr PN: 40-2049AL
Stock: 180
G2 aluminum differential covers are designed to not only protect your ring & pinion, they are designed to help cool your gear oil for prolonged bearing life. Made from high strength heat treated aluminum to withstand direct hits, these covers help protect your investment while adding a distinct look to your vehicle. For Use On Dana 35 Rear Axles Cast From Lightweight Aluminum To Dissipate Heat Raw Aluminum Finish ReinForcing Ribs For Added Rigidity And Strength Heat Treated And Shot Peened To Help Handle A Direct Impact Fully Machined Seal Surface For A Leak Free Installation
Online
$129.99 for EA
Mfr PN: 40-2049AL
Stock: 180

ROLL BAR RAPZ PAIR BLACK ROLL BAR RAPZ PAIR BLACK
Online
$30.65 for EA
Mfr PN: 12501
Stock: 173
Neoprene Roll Bar Wrap; 2 x 50in lengths; Roll bar Rapz are a neoprene-backed wrap with "hook-and-loop" fasteners. Rapz are designed to wrap around or cover up almost any round or square tube item. This product can not be returned.
Online
$30.65 for EA
Mfr PN: 12501
Stock: 173

Classic Fairway Golf Cart Seat Blanket/Cover - Houndstooth Classic Fairway Golf Cart Seat Blanket/Cover - Houndstooth
Online
$26.77 for Each
Retail $29.99
Mfr PN: 40-027-015701-00
Stock: 155
Classic Accessories Golf Cart Seat Blanket (Houndstooth), is instant protection from hot, cold or dirty golf car seats! The Classic Accessories Fairway Golf collection features quilted water-resistant blanket made of heavy-duty fabric for durable performance, allowing you to focus on the game, not the forecast. This blanket feature: Quilted top with plush fleece backing and reflective piping, Wipe-clean, water-resistant, heavy-duty fabric. Quickly secures over golf cart arm rests. Also great as a lap blanket which self-packs for easy transport Exterior pocket offers storage and placement for personalized embroidery. Fleece thumb tab. Machine washable. One size fits most two-person golf cart seats with armrests. We Cover Your Gear!
Online
$26.77 for Each
Retail $29.99
Mfr PN: 40-027-015701-00
Stock: 155

TRANSMISSION SKID PLATE TRANSMISSION SKID PLATE
Online
$143.99 for EA
Retail $155.99
Mfr PN: REA1013
Stock: 145
Rubicon Express has everything you need to protect the vulnerable undercarriage of your 07+ Jeep Wrangler JK from front to back, with skid plates for your engine oil pan, transfer case, and fuel tank. All of the skidplates are CNC laser cut from 3/16-inch steel to withstand even the worst abuse, and are designed to mount up tight to the drivetrain to maximize ground clearance. The modular protection system allows you to add skidplates as your needs and budget allow without any concerns about compatibility.
Online
$143.99 for EA
Retail $155.99
Mfr PN: REA1013
Stock: 145

TIE BAR TIE BAR
Online
$22.65 for EA
Mfr PN: 97510-22
Stock: 115
TIE BAR
Online
$22.65 for EA
Mfr PN: 97510-22
Stock: 115

Paracord Grab Handle - Roll Bar Paracord Grab Handle - Roll Bar
Online
$60.37 for EA
Mfr PN: TAOGHUPBB
Stock: 106
The Paracord Grab handles are made from the same cord material that you can find on parachutes. The material is woven into a tough looking grab hand and will fit padded or non-padded roll bars. They have metal hardware and a griping backing so that they stay put when you’re pushing the vehicle to the limits. Trek Armor has over 17 years of combined experience in manufacturing cutting and sewing products for the U.S. military, you can be sure that what we produce is absolutely top of the line.
Online
$60.37 for EA
Mfr PN: TAOGHUPBB
Stock: 106

6 PIECE ROLL BAR 6 PIECE ROLL BAR
Online
$63.99 for EA
Mfr PN: 769701
Stock: 101
Part Number: S/B769701 Roll Bar Accessory Kit 6 Pc. RollBar Acessy Pack Incl: 769310 - 2 Extreme Grab Handles/769541 First Aid Stg Bag/769901 -2 Roll Bar Mount Drink Hldr/769560 Personal Device Holder
Online
$63.99 for EA
Mfr PN: 769701
Stock: 101

Roll Bar Mounted Fire Extinguisher Holder - 1.5lb. Roll Bar Mounted Fire Extinguisher Holder - 1.5lb.
Online
$15.99 for EA
Mfr PN: 769530
Stock: 85
This handy 1.5 pound fire extinguisher holder will keep your entinguisher stored safely and securely to your off-road rig's 2-3 inch roll bar and off of the floorboard during dicey off-road driving conditions. Use with 1.5-4 inch Sport/Roll Bar Attaches using heavy-duty hook and loop straps Works with 1.5 pound Fire Exinguishers Available in black only
Online
$15.99 for EA
Mfr PN: 769530
Stock: 85

FLOOR PAN PLUG FLOOR PAN PLUG
Online
$3.99 for EA
Retail $3.99
Mfr PN: 55397226AA
Stock: 82
For over 50 years, Crown Automotive has been the leading manufacturer and distributor of replacement parts for Jeep® vehicles. With over 8,000 different part numbers, including many factory-discontinued items, we offer you exceptional quality that is only matched by an exceptional warranty.
Online
$3.99 for EA
Retail $3.99
Mfr PN: 55397226AA
Stock: 82

Dana 50/60/70 Aluminum Cover Dana 50/60/70 Aluminum Cover
Online
$129.99 for EA
Mfr PN: 40-2034AL
Stock: 78
G2 aluminum differential covers are designed to not only protect your ring & pinion, they are designed to help cool your gear oil for prolonged bearing life. Made from high strength heat treated aluminum to withstand direct hits, these covers help protect your investment while adding a distinct look to your vehicle. For Use On Dana 50/60/70 Front Or Rear Axles Cast From Lightweight Aluminum To Dissipate Heat Raw Aluminum Finish ReinForcing Ribs For Added Rigidity And Strength Heat Treated And Shot Peened To Help Handle A Direct Impact Fully Machined Seal Surface For A Leak Free Installation
Online
$129.99 for EA
Mfr PN: 40-2034AL
Stock: 78

Roll Bar Padding Kit Roll Bar Padding Kit
Online
$21.82 for EA
Retail $22.99
Mfr PN: 769115
Stock: 72
Roll Bar Padding Kit Black Denim Pair For Window Braces
Online
$21.82 for EA
Retail $22.99
Mfr PN: 769115
Stock: 72