Toyota 8.9in. 12 Bolt Air Locking Differential Toyota 8.9in. 12 Bolt Air Locking Differential
Online
$1029.60 for EA
Retail $1593.66
Mfr PN: RD142
Stock: 8
The ARB Air Locker is a pneumatic locking differential that uses air to facilitate the locking of both axles. This action converts your differential from a conventional open to a full spool type axle supplying 100% power to both wheels to keep you going through the worst terrain. ARB onboard air compressor required to activate Air Lockers. SOLD SEPARATELY. For Use With 30 Spline Full Floating Axles For Use With All Ratios Air Activated Selectable Locker Converts From Open Differential To fully Locked Or Spool Simple Push Button Operation Requires Air Compressor SOLD SEPARATELY
Online
$1029.60 for EA
Retail $1593.66
Mfr PN: RD142
Stock: 8

RING WHEEL BRG RET RING WHEEL BRG RET
Online
$12.99 for EA
Retail $14.24
Mfr PN: 36797
Stock: 195
RING WHEEL BRG RET
Online
$12.99 for EA
Retail $14.24
Mfr PN: 36797
Stock: 195

DANA 44 DIFF COVER - PC DANA 44 DIFF COVER - PC
Online
$132.10 for EA
Mfr PN: 42-11-044-PC
Stock: 1358
Poison Spyder Bombshell Diff Covers are designed to protect your gears, lockers and diff cover bolts from the most punishing rocks and trail hazards. The stock covers your Jeep came with are weak, stamped sheetmetal. Even a moderate tap with a rock can cave it in against your ring gear, causing potential damage to the gears, locker and carrier bearings, not to mention a difficult, messy trail fix. Even more common, though less catastrophic, is "peel back" that can occur when sliding over a rock causes the lip of the cover to peel up, allowing your gear oil to drain causing a hazard for both your Jeep and the environment. The Bombshell Diff Cover is your best insurance against each of these hazards. The Bombshell differential cover is cast from highly ductile nodular iron—the same material drag racing differential housings are cast from to handle thousands of horsepower. The design of the Bombshell incorporates recesses to protect the diff cover bolt heads from trail damage, while the profile of the Bombshell acts as a ramp to help slide your Jeep up and over the most troublesome pumpkin-eaters. The ramp profile also results in an extremely thick & up to 1" thick—cross-section around the bolt ring, where contact with the rocks is most likely. Throughout the rest of its cross-section the Bombshell is the thickest cast differential cover on the market, from 7/16" to a brutal 1/2" thick at the outermost surface.
Online
$132.10 for EA
Mfr PN: 42-11-044-PC
Stock: 1358

Toyota 8.9in. C-Clip Air Locking Differential Toyota 8.9in. C-Clip Air Locking Differential
Online
$1029.60 for EA
Retail $1593.66
Mfr PN: RD153
Stock: 12
The ARB Air Locker is a pneumatic locking differential that uses air to facilitate the locking of both axles. This action converts your differential from a conventional open to a full spool type axle supplying 100% power to both wheels to keep you going through the worst terrain. ARB onboard air compressor required to activate Air Lockers. SOLD SEPARATELY. For Use With 30 Spline C Clip Axles For Use With All Ratios Air Activated Selectable Locker Converts From Open Differential To fully Locked Or Spool Simple Push Button Operation Requires Air Compressor SOLD SEPARATELY
Online
$1029.60 for EA
Retail $1593.66
Mfr PN: RD153
Stock: 12

Ford 8.8in. 4.88 Ratio Ford 8.8in. 4.88 Ratio
Online
$224.99 for EA
Mfr PN: 2-2013-488
Stock: 179
G2 Performance Ring & Pinion sets are engineered with todays most demanding applications in mind. Designed to hold up to oversized tires and high performance engines, these gears use use the latest technology and materials in their manufacturing to give you the strongest and quietest performance gear sets available. For Use Will All Ratio Carriers 10 Year Warranty Computer Heat Treated 8620 Steel Manufactured To O.E. Specifications Double Shot Peened Double Lapped
Online
$224.99 for EA
Mfr PN: 2-2013-488
Stock: 179

AXLE BEARING D44 REAR AXLE BEARING D44 REAR
Online
$33.99 for EA
Mfr PN: 565903
Stock: 222
AXLE BEARING D44 REAR
Online
$33.99 for EA
Mfr PN: 565903
Stock: 222

Dana 30 XJ/YJ Front Reverse 4.88 Ratio Dana 30 XJ/YJ Front Reverse 4.88 Ratio
Online
$194.99 for EA
Mfr PN: 2-2032-488R
Stock: 127
G2 Performance Ring & Pinion sets are engineered with todays most demanding applications in mind. Designed to hold up to oversized tires and high performance engines, these gears use use the latest technology and materials in their manufacturing to give you the strongest and quietest performance gear sets available. For Use In 84-99 Jeep XJ Cherokee Front For Use In 87-96 Jeep YJ Wrangler Front For Use With 3.73 And Up Carrier 10 Year Warranty Computer Heat Treated 8620 Steel Manufactured To O.E. Specifications Double Shot Peened Double Lapped
Online
$194.99 for EA
Mfr PN: 2-2032-488R
Stock: 127

Inflation Accessory Kit Inflation Accessory Kit
Online
$39.22 for EA
Retail $53.32
Mfr PN: 171302
Stock: 108
Carrying the appropriate tire accessories is essential when you're traveling off road. Not only do tires require regular PSI adjustment to suit differing terrain, it's not unusual to get several punctures in one day.
Online
$39.22 for EA
Retail $53.32
Mfr PN: 171302
Stock: 108

Dana 44 30 Spline Lock Right Locker Dana 44 30 Spline Lock Right Locker
Online
$440.18 for EA
Retail $569.98
Mfr PN: 2410-LR
Stock: 4
Brute Force Devices For Rugged Applications,Best Value For Greatly Increased Traction,Complete Replacement Of Diff. Case Not Req.,Simple Installation,Ring And Pinion Setup Not Altered,Installs Easily In Front/Rear Or Both,Proven In Most Demanding Applications For Use With 30 Spline Axles For Open Differential Only No Need To Set Up Gears Reuses Existing Carrier Arrgesive Traction
Online
$440.18 for EA
Retail $569.98
Mfr PN: 2410-LR
Stock: 4

Super-Flex™ Assembly Super-Flex™ Assembly
Online
$41.41 for EA
Mfr PN: RE3792
Stock: 379
The Rubicon Express Super-Flex cartridge was originally designed to replace the heim joints used in our early suspension designs. The large size joint is designed to fit directly into the factory front or rear lower control arm mounting points on the XJ/MJ/ZJ/TJ/WJ chassis. This cartridge uses UHMW side races and a unique threaded adjuster nut which allows easy tightening and rebuilding if necessary. Rubicon Express ran their JeepSpeed race Cherokee for a complete season on one set of control arms with Super-Flex Joints, without a single failure. After removal at the end of the season, they felt as tight as the day they were installed. In contrast, factory rubber bushings need to be replaced EVERY RACE!
Online
$41.41 for EA
Mfr PN: RE3792
Stock: 379

DL-SP-1310-1330-1350- SLINGER DL-SP-1310-1330-1350- SLINGER
Online
$6.99 for EA
Retail $7.70
Mfr PN: 2-86-418
Stock: 31
SEAL
Online
$6.99 for EA
Retail $7.70
Mfr PN: 2-86-418
Stock: 31

D44 OUTER AXLE OIL SEAL D44 OUTER AXLE OIL SEAL
Online
$7.99 for EA
Mfr PN: 35239
Stock: 52
D44 OUTER AXLE OIL SEAL
Online
$7.99 for EA
Mfr PN: 35239
Stock: 52

AXLE SEAL D30 27SPL AXLE SEAL D30 27SPL
Online
$4.99 for EA
Retail $5.24
Mfr PN: 470160
Stock: 73
AXLE SEAL D30 27SPL
Online
$4.99 for EA
Retail $5.24
Mfr PN: 470160
Stock: 73

2.5 Inch Forged Johnny Joint® with 1-1/4" RH Threaded Stud 2.5 Inch Forged Johnny Joint® with 1-1/4" RH Threaded Stud
Online
$56.05 for EA
Retail $73.98
Mfr PN: CE-9114
Stock: 39
Forged Johnny Joint® rod ends feature forged steel construction, a 1-1/4"-12 right hand threaded shank and come fully assembled with our standard Johnny Joint® internals (2.625" wide ball center with a 9/16" thru bolt hole). These units are externally greasable via a zerk fitting. Units will also accept our 9/16" greasable thru bolts as well (available seperately). Finished in gold zinc plating. We also keep the jam nuts for these units on hand at all times as well. These can be used in any Currie adjustable lower control arm, as well as in any type of universal application for those building their own arms.
Online
$56.05 for EA
Retail $73.98
Mfr PN: CE-9114
Stock: 39

Super-Flex™ Assembly Super-Flex™ Assembly
Online
$35.99 for EA
Mfr PN: RE3791
Stock: 92
The Rubicon Express Super-Flex cartridge was originally designed to replace the heim joints used in our early suspension designs. The small size joint is designed to fit directly into the factory front or rear upper control arm mounting points on the XJ/MJ/ZJ/TJ/WJ chassis. This cartridge uses UHMW side races and a unique threaded adjuster nut which allows easy tightening and rebuilding if necessary. Rubicon Express ran their JeepSpeed race Cherokee for a complete season on one set of control arms with Super-Flex Joints, without a single failure. After removal at the end of the season, they felt as tight as the day they were installed. In contrast, factory rubber bushings need to be replaced EVERY RACE!
Online
$35.99 for EA
Mfr PN: RE3791
Stock: 92

Heavy Duty Transfer Case Mount Kit Heavy Duty Transfer Case Mount Kit
Online
$104.37 for EA
Mfr PN: 105100-1-KIT
Stock: 0
The Trail Gear's HD T case mount is stamped out of 1/4in. thick steel plate, and then welded on a jig to ensure the best fit possible.These T case mount kits are coated with a zinc for a finish that will last a lifetime.The bushings are polyurethane for long lasting performance and durability.
Online
$104.37 for EA
Mfr PN: 105100-1-KIT
Stock: 0

REAR CRATE AXEL REAR CRATE AXEL
Online
$5195.31 for EA
Mfr PN: 10005942
Stock: 0
Wherever limits are pushed, Dana is there. That's why we've introduced the new Ultimate Dana 60 front and rear axles for the Jeep Wrangler JK. Not only is it the biggest, strongest Dana 60 axle we've ever built, but it also incorporates many of the upgrades that off-roaders demand. You get a direct-fit, bolt-in solution for your Jeep Wrangler JK, plus the unparalleled technology, strength, and durability that comes from having Spicer Inside
Online
$5195.31 for EA
Mfr PN: 10005942
Stock: 0

54MM AXLE SOCKET 54MM AXLE SOCKET
Online
$18.99 for EA
Retail $19.99
Mfr PN: 140157-1-KIT
Stock: 16
Do you need to tighten or replace your wheel bearings? Then your going to need Mile Marker's Spindle Nut Socket.
Online
$18.99 for EA
Retail $19.99
Mfr PN: 140157-1-KIT
Stock: 16

Driveshaft Bolt Driveshaft Bolt
Online
$8.48 for EA
Mfr PN: 6036415AA
Stock: 58
This is a OE Factory driveshaft bolt from Jeep. Use this to replace broken or stripped driveshaft bolts. Sold individually.
Online
$8.48 for EA
Mfr PN: 6036415AA
Stock: 58

Truss Upper Link Mounts Truss Upper Link Mounts
Online
$32.46 for EA
Mfr PN: BR1044
Stock: 1
These Link Mounts are designed to mount on a flat surface such as a truss. They are CNC cut and bent from 1/4" thick mild steel. The bend strengthens the mount so no additional reinforcement is needed. 2.63" inner width. Please note this requires welding and general fabrication.
Online
$32.46 for EA
Mfr PN: BR1044
Stock: 1

2.5 Inch Forged Johnny Joint® with 1" RH Threaded Stud 2.5 Inch Forged Johnny Joint® with 1" RH Threaded Stud
Online
$56.05 for EA
Mfr PN: CE-9113
Stock: 4
All new from Currie, forged Johnny Joints®!!! We have taken the Johnny Joint® to the next level by making a male rod end style forging that accepts the Johnny Joint® internals from our CE-9112 2" Johnny Joints®. This version features a 7/16" thru bolt hole, a 2" mounting width, 2 1/4" of 3/4"-16 right hand threads on the shank, and is greasable through the outer shell. Units will also accept our 7/16" greasable thru bolts as well (available seperately). We also keep the jam nuts for these units on hand at all times as well. These can be used in any Currie adjustable upper control arm, as well as in any type of universal application for those building their own arms. Finished in gold zinc plating, sold each.
Online
$56.05 for EA
Mfr PN: CE-9113
Stock: 4

Ford 8.8in. Early Master Installation Kit Ford 8.8in. Early Master Installation Kit
Online
$112.99 for EA
Mfr PN: 35-2013
Stock: 103
G2 Master kits include all the parts that are needed to properly install a ring and pinion. These G2 kits include hard to find parts like a proper shim kit, replacement pinion nut , crush sleeve, pinion seal, pinion bearings, carrier bearings, ring gear bolts, silicone sealer, locktite and gear marking compound. these are the parts that the auto parts store never seems to have or ever herd of. For Use In 2008 And Earlier Axles Pinion Nut Pinion Seal Timken Outer Pinion Bearing And Race Crush Sleeve Timken Inner Pinion Bearing And Race Pinion Shims Carrier Shims Carrier Bearings And Races Ring Gear Bolts Thread Locking Compound Gear Marking Compound Silicone Sealer
Online
$112.99 for EA
Mfr PN: 35-2013
Stock: 103

JK Rear Tracbar Bracket JK Rear Tracbar Bracket
Online
$57.98 for EA
Mfr PN: JK4426
Stock: 12
This heavy bracket is designed to take serious abuse and replace your worn JK factory rear tracbar bracket. The 1/4" thick precision cut and formed components of this setup out perform the competition. Note: This bracket offers several raised tracbar holes. Every lift is different and some trial and error may be necessary to find the ideal ride. This bracket is NOT bolt on and requires welding to install.
Online
$57.98 for EA
Mfr PN: JK4426
Stock: 12

GM 10BOLT 8.5in 30 SPL GM 10BOLT 8.5in 30 SPL
Online
$584.08 for EA
Retail $705.99
Mfr PN: 19559-010
Stock: 1
The Eaton Posi is one of the top performers when it comes to streetable performance form a limited slip differential. The Eaton Posi uses preload Springs with Carbon Fiber clutches and is rebuildable.
Online
$584.08 for EA
Retail $705.99
Mfr PN: 19559-010
Stock: 1

Dana 60 35 Spline 4.56 Up Air Locking Differential Dana 60 35 Spline 4.56 Up Air Locking Differential
Online
$1159.60 for EA
Retail $1770.94
Mfr PN: RD166
Stock: 11
The ARB Air Locker is a pneumatic locking differential that uses air to facilitate the locking of both axles. This action converts your differential from a conventional open to a full spool type axle supplying 100% power to both wheels to keep you going through the worst terrain. ARB onboard air compressor required to activate Air Lockers. SOLD SEPARATELY. For Use With 35 Spline Axles For Use With 4.56 And Up Gears Air Activated Selectable Locker Converts From Open Differential To fully Locked Or Spool Simple Push Button Operation Requires Air Compressor SOLD SEPARATELY
Online
$1159.60 for EA
Retail $1770.94
Mfr PN: RD166
Stock: 11

GM 8.5in. 10 Bolt Front Axle Spindle GM 8.5in. 10 Bolt Front Axle Spindle
Online
$124.99 for EA
Mfr PN: 99-2021-1
Stock: 26
G2 has these high strength replacement spindles available for most popular applications. No more searching salvage yards only to find worn out spindles. GM 8.5in. 10 Bolt Front Axle Spindle By G2 Precision Machined From Forged Steel 6 Bolt Mounting Pattern For Use On 1977-1991 GM K5 And Suburban 1/2 &3/4 ton For Use On 1977-1987 GM 1/2 & 3/4 Ton Truck
Online
$124.99 for EA
Mfr PN: 99-2021-1
Stock: 26

DIFF COVER D60/D50 BLACK DIFF COVER D60/D50 BLACK
Online
$228.96 for EA
Retail $236.99
Mfr PN: 0750001B
Stock: 4
When off road, it is inevitable that obstacles and off road hazards will be encountered that could potentially inflict expensive damage to your differential. to prevent this, ARB manufactures the differential cover. Using high tensile nodular iron, it has been engineered to protect the differential and ring and pinion set from any off road hazards. Features: Computer optimized cross brace design increases the structural rigidity of the whole axle. Additional housing strength helps keep the ring & pinion gears meshing on the flat faces of the teeth, greatly increasing ring & pinion life and overall maximum load strength. Top quality, high power neodymium magnets are used in both the Drain Plug and the dipstick to collect metallic wear particles as the vehicle moves. Magnet location in the end of the dipstick allows the oil to be checked For tell-tale signs of Internal damage.
Online
$228.96 for EA
Retail $236.99
Mfr PN: 0750001B
Stock: 4

1.25"-12 RH Jam Nut 1.25"-12 RH Jam Nut
Online
$3.99 for EA
Retail $3.98
Mfr PN: CE-9114JN
Stock: 19
1.25"-12 right hand thread jam nut for use on Currie CE-9114 Johnny Joints® with treaded shanks, or in any other application that would need a 1.25" jam nut. Silver zinc plated, sold each.
Online
$3.99 for EA
Retail $3.98
Mfr PN: CE-9114JN
Stock: 19

Dana 30 Inner Axle Seal Dana 30 Inner Axle Seal
Online
$5.99 for EA
Retail $5.60
Mfr PN: 46470
Stock: 133
These seals are one of the most overlooked components in the from axle rebuilding process. These seals seal the housing to the axle shaft and prevent gear oil from running out your axle tubes.
Online
$5.99 for EA
Retail $5.60
Mfr PN: 46470
Stock: 133

GM 8.5in. 10 Bolt 4.56 Ratio GM 8.5in. 10 Bolt 4.56 Ratio
Online
$224.99 for EA
Mfr PN: 2-2021-456
Stock: 101
G2 Performance Ring & Pinion sets are engineered with todays most demanding applications in mind. Designed to hold up to oversized tires and high performance engines, these gears use use the latest technology and materials in their manufacturing to give you the strongest and quietest performance gear sets available. For Use With 2.73 Up Carrier Will Work In 8.6in. With 35-2022 Master Kit 10 Year Warranty Computer Heat Treated 8620 Steel Manufactured To O.E. Specifications Double Shot Peened Double Lapped
Online
$224.99 for EA
Mfr PN: 2-2021-456
Stock: 101

Dana 30 TJ/WJ/XJ/ZJ Short 4.56 Ratio Dana 30 TJ/WJ/XJ/ZJ Short 4.56 Ratio
Online
$194.99 for EA
Mfr PN: 2-2031-456
Stock: 182
G2 Performance Ring & Pinion sets are engineered with todays most demanding applications in mind. Designed to hold up to oversized tires and high performance engines, these gears use use the latest technology and materials in their manufacturing to give you the strongest and quietest performance gear sets available. For Use In 97-05 Jeep TJ Wrangler Front For Use In 99 -05 Jeep WJ Grand Cherokee Front For Use In 00-05 Jeep XJ Cherokee Front For Use In 96.5-98 Jeep ZJ Grand Cherokee Front For Use With 3.73 And Up Carrier 10 Year Warranty Computer Heat Treated 8620 Steel Manufactured To O.E. Specifications Double Shot Peened Double Lapped
Online
$194.99 for EA
Mfr PN: 2-2031-456
Stock: 182

Track Bar Bracket Front XJ/ZJ 4.5"-7.5" Track Bar Bracket Front XJ/ZJ 4.5"-7.5"
Online
$81.99 for EA
Mfr PN: RE1665
Stock: 230
Extra H.D.front track bar bracket for Cherokee and Grand Cherokee. This drop bracket is required for installation of RE1660.
Online
$81.99 for EA
Mfr PN: RE1665
Stock: 230